Skip to main content

What is Cisco Chassis, Backplane, Line Card

What does Chassis means?
A Chassis is a frame/housing for mounting the circuit components for Cisco Switches and Routers or any type of devices that provides power and a high-speed backplane. The frame also protects all of the vital internal equipment from dust, moisture, and tampering. 

Making the Chassis to define even easier is; 
A chassis is an enclosure; a container that holds things together... i.e. an egg carton holds eggs together inside. A chassis does the same thing; it holds the important things inside like wiring, power supplies etc. 

What does Backplane means?
Backplane is a circuit board with sockets that allows Supervisor engines Cards or modules to be inserted into these sockets and connect them to each other. Backplane is mounted on the Chassis. 

Modules or line cards provide different types of interfaces, but the processing of packets is usually done in the Supervisor engine. Backplane is the medium for data flow between modules and Supervisor engines. 

Additionally, most high-end switches off-load processing away from the supervisors, allowing line cards to switch traffic directly between ports on the same card without using any processing power or even touching the backplane. Naturally, this can't be done for all traffic, but basic layer-2 switching can usually be handled exclusively by the line card, and in many cases also more complex operations can be handled as well. 

What does Line Card means?
The line cards provide interfaces to the network.
Labels:

Comments

Post a Comment

Popular posts from this blog

How to import Putty Saved Connections to mRemoteNG

Just started using mRemoteNG and its being very cool to connect to different remote connection with different protocols e.g Window Remote Desktop, VNC to Linux, SSH, HTTP connection etc. from a single application. As new user I configured some remote desktop connection which was quite easy to figure out. But when I wanted to add SSH connections, it came in my mind to import all of the saved connections in the putty. But I couldn't figure it out how can it be done, though it was quite easy and here are the steps. Open your mRemoteNG Create a folder if you want segregation of multiple networks Create a new connection Enter the IP address of remote server under connection in Config pane Under the config pane, select protocol " SSH version 2 ".  Once you select protocol to SSH version 2 you are given option to import putty sessions, as shown in the snap below. In the above snap, I have imported CSR-AWS session from my saved sessions in Putty.
1 comment
Read more

BGP Soft Reconfiguration vs. Route Refresh: Key Differences and Best Practices

In BGP (Border Gateway Protocol), managing route updates and reapplying new policies can sometimes be challenging, especially if you want to avoid resetting the BGP session. Two methods allow you to update routing policies without tearing down the session: BGP Soft Reconfiguration and BGP Route Refresh . While both methods serve the same purpose, they work differently and have distinct impacts on your router's resources. This post explains the key differences between Soft Reconfiguration and Route Refresh , when to use each, and why Route Refresh is preferred in most modern networks. 1. What is BGP Soft Reconfiguration? BGP Soft Reconfiguration is an older method of applying new policies (like route maps, filters, or prefix lists) without resetting the BGP session. It works by storing a local copy of all the routes received from a BGP neighbor before applying inbound policies. This local route copy allows the router to reprocess the routes when a policy change occurs. How So...
Post a Comment
Read more

BGP Local Preference Controlling Outbound Traffic in BGP

In BGP, Local Preference is used to control the outbound traffic path. It helps you decide which egress point (exit point) should be used when you have multiple connections to external networks, such as ISPs. Local Preference is an attribute that is local to your AS and is shared with all iBGP peers but not with eBGP neighbors. Higher Local Preference = More preferred outbound path. Example Scenario : You have two external links: ISP1 (via CE1) and ISP2 (via CE2). You want traffic to prefer ISP1 for all outbound traffic. Network Topology : CE1 (connected to ISP1): 10.0.1.1/30 CE2 (connected to ISP2): 10.0.2.1/30 iBGP Router (Internal) connected to both CE1 (10.0.1.2/30) and CE2 (10.0.2.2/30). Configuration on CE1 (Higher Local Preference) : Create a route map to set the local preference to 200 for routes learned from CE1: route-map SET_LOCAL_PREF permit 10 set local-preference 200 In the BGP configuration for CE1, apply this route map to the neighbor: router bgp 65001 ne...
Post a Comment
Read more